logicanalyzer/Firmware/LogicAnalyzer/build/LogicAnalyzer.pio.h

// -------------------------------------------------- //
// This file is autogenerated by pioasm; do not edit! //
// -------------------------------------------------- //

#pragma once

#if !PICO_NO_HARDWARE
#include "hardware/pio.h"
#endif

// ---------------- //
// POSITIVE_CAPTURE //
// ---------------- //

#define POSITIVE_CAPTURE_wrap_target 4
#define POSITIVE_CAPTURE_wrap 5

static const uint16_t POSITIVE_CAPTURE_program_instructions[] = {
    0x80a0, //  0: pull   block                      
    0x6020, //  1: out    x, 32                      
    0x80a0, //  2: pull   block                      
    0x6040, //  3: out    y, 32                      
            //     .wrap_target
    0x4000, //  4: in     pins, 32                   
    0x00c6, //  5: jmp    pin, 6                     
            //     .wrap
    0x4000, //  6: in     pins, 32                   
    0x0046, //  7: jmp    x--, 6                     
    0x4040, //  8: in     y, 32                      
    0xc000, //  9: irq    nowait 0                   
    0x000a, // 10: jmp    10                         
};

#if !PICO_NO_HARDWARE
static const struct pio_program POSITIVE_CAPTURE_program = {
    .instructions = POSITIVE_CAPTURE_program_instructions,
    .length = 11,
    .origin = -1,
};

static inline pio_sm_config POSITIVE_CAPTURE_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + POSITIVE_CAPTURE_wrap_target, offset + POSITIVE_CAPTURE_wrap);
    return c;
}
#endif

// ---------------- //
// NEGATIVE_CAPTURE //
// ---------------- //

#define NEGATIVE_CAPTURE_wrap_target 0
#define NEGATIVE_CAPTURE_wrap 10

static const uint16_t NEGATIVE_CAPTURE_program_instructions[] = {
            //     .wrap_target
    0x80a0, //  0: pull   block                      
    0x6020, //  1: out    x, 32                      
    0x80a0, //  2: pull   block                      
    0x6040, //  3: out    y, 32                      
    0x4000, //  4: in     pins, 32                   
    0x00c4, //  5: jmp    pin, 4                     
    0x4000, //  6: in     pins, 32                   
    0x0046, //  7: jmp    x--, 6                     
    0x4040, //  8: in     y, 32                      
    0xc000, //  9: irq    nowait 0                   
    0x000a, // 10: jmp    10                         
            //     .wrap
};

#if !PICO_NO_HARDWARE
static const struct pio_program NEGATIVE_CAPTURE_program = {
    .instructions = NEGATIVE_CAPTURE_program_instructions,
    .length = 11,
    .origin = -1,
};

static inline pio_sm_config NEGATIVE_CAPTURE_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + NEGATIVE_CAPTURE_wrap_target, offset + NEGATIVE_CAPTURE_wrap);
    return c;
}
#endif

// --------------- //
// COMPLEX_CAPTURE //
// --------------- //

#define COMPLEX_CAPTURE_wrap_target 5
#define COMPLEX_CAPTURE_wrap 6

static const uint16_t COMPLEX_CAPTURE_program_instructions[] = {
    0x80a0, //  0: pull   block                      
    0x6020, //  1: out    x, 32                      
    0x80a0, //  2: pull   block                      
    0x6040, //  3: out    y, 32                      
    0x20c7, //  4: wait   1 irq, 7                   
            //     .wrap_target
    0x401d, //  5: in     pins, 29                   
    0x00c7, //  6: jmp    pin, 7                     
            //     .wrap
    0x401d, //  7: in     pins, 29                   
    0x0047, //  8: jmp    x--, 7                     
    0x4040, //  9: in     y, 32                      
    0xc000, // 10: irq    nowait 0                   
    0x000b, // 11: jmp    11                         
};

#if !PICO_NO_HARDWARE
static const struct pio_program COMPLEX_CAPTURE_program = {
    .instructions = COMPLEX_CAPTURE_program_instructions,
    .length = 12,
    .origin = -1,
};

static inline pio_sm_config COMPLEX_CAPTURE_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + COMPLEX_CAPTURE_wrap_target, offset + COMPLEX_CAPTURE_wrap);
    return c;
}
#endif

// ------------ //
// FAST_CAPTURE //
// ------------ //

#define FAST_CAPTURE_wrap_target 4
#define FAST_CAPTURE_wrap 5

static const uint16_t FAST_CAPTURE_program_instructions[] = {
    0x80a0, //  0: pull   block                      
    0x6020, //  1: out    x, 32                      
    0x80a0, //  2: pull   block                      
    0x6040, //  3: out    y, 32                      
            //     .wrap_target
    0x401d, //  4: in     pins, 29                   
    0x00c6, //  5: jmp    pin, 6                     
            //     .wrap
    0x401d, //  6: in     pins, 29                   
    0x0046, //  7: jmp    x--, 6                     
    0x4040, //  8: in     y, 32                      
    0xc000, //  9: irq    nowait 0                   
    0x000a, // 10: jmp    10                         
};

#if !PICO_NO_HARDWARE
static const struct pio_program FAST_CAPTURE_program = {
    .instructions = FAST_CAPTURE_program_instructions,
    .length = 11,
    .origin = -1,
};

static inline pio_sm_config FAST_CAPTURE_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + FAST_CAPTURE_wrap_target, offset + FAST_CAPTURE_wrap);
    return c;
}

#include "hardware/gpio.h"
#include "hardware/dma.h"
#include "hardware/irq.h"
#include "string.h"
#include "hardware/sync.h"
//Static variables for the PIO programs
static PIO capturePIO;
static PIO triggerPIO;
static uint sm_Capture;
static uint captureOffset;
static uint sm_Trigger;
static uint triggerOffset;
//Static variables for DMA channels
static uint32_t dmaPingPong0;
static uint32_t dmaPingPong1;
static uint32_t dmaPingPong2;
static uint32_t dmaPingPong3;
//Static information of the last capture
static uint8_t lastCapturePins[24];         //List of captured pins
static uint8_t lastCapturePinCount;         //Count of captured pins
static uint32_t lastTriggerCapture;         //Moment where the trigger happened inside the circular pre buffer
static uint32_t lastPreSize;                //Pre-trigger buffer size
static uint32_t lastPostSize;               //Post-trigger buffer size
static bool lastTriggerInverted;            //Inverted?
static uint8_t lastTriggerPin;
static uint32_t lastStartPosition;
static bool lastCaptureComplexFast;
static uint8_t lastCaptureType;
static uint8_t lastTriggerPinBase;
static uint32_t lastTriggerPinCount;
//Static information of the current capture
static bool captureFinished;
static bool captureProcessed;
//Pin mapping, used to map the channels to the PIO program
//Could be stored into flash memory but it causes problems
const uint8_t pinMap[] = {2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,26,27,28};
//Main capture buffer, aligned at a 32k boundary, to use the maxixmum ring size supported by DMA channels
static uint32_t captureBuffer[32 * 1024] __attribute__((aligned(32768)));
//-----------------------------------------------------------------------------
//--------------Complex trigger PIO program------------------------------------
//-----------------------------------------------------------------------------
#define COMPLEX_TRIGGER_wrap_target 0
#define COMPLEX_TRIGGER_wrap 8
#define CAPTURE_TYPE_SIMPLE 0
#define CAPTURE_TYPE_COMPLEX 1
#define CAPTURE_TYPE_FAST 2
uint16_t COMPLEX_TRIGGER_program_instructions[] = {
            //     .wrap_target
    0x80a0, //  0: pull   block                      
    0x6020, //  1: out    x, 32                      
    0xe000, //  2: set    pins, 0                    
    0xc007, //  3: irq    nowait 7                   
    0xa0e0, //  4: mov    osr, pins                  
    0x6044, //  5: out    y, 4                       
    0x00a4, //  6: jmp    x != y, 4                  
    0xe001, //  7: set    pins, 1                    
    0x0008, //  8: jmp    8                          
            //     .wrap
};
struct pio_program COMPLEX_TRIGGER_program = {
    .instructions = COMPLEX_TRIGGER_program_instructions,
    .length = 9,
    .origin = -1,
};
static inline pio_sm_config COMPLEX_TRIGGER_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + COMPLEX_TRIGGER_wrap_target, offset + COMPLEX_TRIGGER_wrap);
    return c;
}
//-----------------------------------------------------------------------------
//--------------Complex trigger PIO program END--------------------------------
//-----------------------------------------------------------------------------
//-----------------------------------------------------------------------------
//--------------Fast trigger PIO program---------------------------------------
//-----------------------------------------------------------------------------
#define FAST_TRIGGER_wrap_target 0
#define FAST_TRIGGER_wrap 31
uint16_t FAST_TRIGGER_program_instructions[32];
struct pio_program FAST_TRIGGER_program = {
    .instructions = FAST_TRIGGER_program_instructions,
    .length = 32,
    .origin = 0,
};
static inline pio_sm_config FAST_TRIGGER_program_get_default_config(uint offset) {
    pio_sm_config c = pio_get_default_sm_config();
    sm_config_set_wrap(&c, offset + FAST_TRIGGER_wrap_target, offset + FAST_TRIGGER_wrap);
    sm_config_set_sideset(&c, 1, false, false);
    return c;
}
uint8_t create_fast_trigger_program(uint8_t pattern, uint8_t length)
{
    //This creates a 32 instruction jump table. Each instruction is a MOV PC, PINS except for the addresses that
    //match the specified pattern.
    uint8_t i;
    uint8_t mask = (1 << length) - 1; //Mask for testing address vs pattern
    uint8_t first = 255;
    for(i = 0; i < 32; i++)
    {
        if((i & mask) == pattern)
            FAST_TRIGGER_program_instructions[i] = 0x1000 | i; //JMP i SIDE 1
        else
        {
            FAST_TRIGGER_program_instructions[i] = 0xA0A0;     //MOV PC, PINS SIDE 0
            first = i;
        }
    }
    return first;
}
//-----------------------------------------------------------------------------
//--------------Fast trigger PIO program END-----------------------------------
//-----------------------------------------------------------------------------
void fast_capture_completed() 
{
    //Mark the capture as finished
    captureFinished = true;
    //Abort DMA channels
    dma_channel_abort(dmaPingPong0);
    dma_channel_abort(dmaPingPong1);
    dma_channel_abort(dmaPingPong2);
    dma_channel_abort(dmaPingPong3);
    //Clear PIO interrupt 0 and unhook handler
    pio_interrupt_clear(capturePIO, 0);
    irq_set_enabled(PIO0_IRQ_0, false);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), false);
    irq_remove_handler(PIO0_IRQ_0, fast_capture_completed);
    //Disable all DMA channels
    dma_channel_config c = dma_channel_get_default_config(dmaPingPong0);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong0, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong0);
    c = dma_channel_get_default_config(dmaPingPong1);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong1, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong1);
    c = dma_channel_get_default_config(dmaPingPong2);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong2, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong2);
    c = dma_channel_get_default_config(dmaPingPong3);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong3, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong3);
    //Stop PIO capture program and clear
    pio_sm_set_enabled(capturePIO, sm_Capture, false);
    pio_sm_unclaim(capturePIO, sm_Capture);
    pio_remove_program(capturePIO, &FAST_CAPTURE_program, captureOffset);
    //Stop PIO trigger program and clear
    pio_sm_set_enabled(triggerPIO, sm_Trigger, false);
    pio_sm_set_pins(triggerPIO, sm_Trigger, 0);
    pio_sm_unclaim(triggerPIO, sm_Trigger);
    pio_remove_program(triggerPIO, &FAST_TRIGGER_program, triggerOffset);
}
void complex_capture_completed() 
{
    //Mark the capture as finished
    captureFinished = true;
    //Abort DMA channels
    dma_channel_abort(dmaPingPong0);
    dma_channel_abort(dmaPingPong1);
    dma_channel_abort(dmaPingPong2);
    dma_channel_abort(dmaPingPong3);
    //Clear PIO interrupt 0 and unhook handler
    pio_interrupt_clear(capturePIO, 0);
    irq_set_enabled(PIO0_IRQ_0, false);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), false);
    irq_remove_handler(PIO0_IRQ_0, complex_capture_completed);
    //Disable all DMA channels
    dma_channel_config c = dma_channel_get_default_config(dmaPingPong0);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong0, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong0);
    c = dma_channel_get_default_config(dmaPingPong1);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong1, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong1);
    c = dma_channel_get_default_config(dmaPingPong2);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong2, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong2);
    c = dma_channel_get_default_config(dmaPingPong3);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong3, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong3);
    //Stop PIO capture program and clear
    pio_sm_set_enabled(capturePIO, sm_Capture, false);
    pio_sm_unclaim(capturePIO, sm_Capture);
    pio_remove_program(capturePIO, &COMPLEX_CAPTURE_program, captureOffset);
    //Stop PIO trigger program and clear
    pio_sm_set_enabled(capturePIO, sm_Trigger, false);
    pio_sm_set_pins(capturePIO, sm_Trigger, 0);
    pio_sm_unclaim(capturePIO, sm_Trigger);
    pio_remove_program(capturePIO, &COMPLEX_TRIGGER_program, triggerOffset);
}
void simple_capture_completed() 
{
    //Mark the capture as finished
    captureFinished = true;
    //Abort DMA channels
    dma_channel_abort(dmaPingPong0);
    dma_channel_abort(dmaPingPong1);
    dma_channel_abort(dmaPingPong2);
    dma_channel_abort(dmaPingPong3);
    //Clear PIO interrupt 0 and unhook handler
    pio_interrupt_clear(capturePIO, 0);
    irq_set_enabled(PIO0_IRQ_0, false);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), false);
    irq_remove_handler(PIO0_IRQ_0, simple_capture_completed);
    //Disable and unclaim all DMA channels
    dma_channel_config c = dma_channel_get_default_config(dmaPingPong0);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong0, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong0);
    c = dma_channel_get_default_config(dmaPingPong1);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong1, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong1);
    c = dma_channel_get_default_config(dmaPingPong2);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong2, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong2);
    c = dma_channel_get_default_config(dmaPingPong3);
    channel_config_set_enable(&c, false);
    dma_channel_configure(dmaPingPong3, &c, 0, 0, 0, false);
    dma_channel_unclaim(dmaPingPong3);
    //Stop PIO program and clear
    pio_sm_set_enabled(capturePIO, sm_Capture, false);
    pio_sm_unclaim(capturePIO, sm_Capture);
    if(lastTriggerInverted)
        pio_remove_program(capturePIO, &POSITIVE_CAPTURE_program, captureOffset);
    else
        pio_remove_program(capturePIO, &NEGATIVE_CAPTURE_program, captureOffset);
}
void configureCaptureDMAs()
{
    //Claim four DMA channels, each channel writes to 32Kb of the buffer (8192 samples) as that's the maximum ring size supported
    dmaPingPong0 = dma_claim_unused_channel(true);
    dmaPingPong1 = dma_claim_unused_channel(true);
    dmaPingPong2 = dma_claim_unused_channel(true);
    dmaPingPong3 = dma_claim_unused_channel(true);
    //Configure first capture DMA
    dma_channel_config dmaPingPong0Config = dma_channel_get_default_config(dmaPingPong0);
    channel_config_set_read_increment(&dmaPingPong0Config, false); //Do not increment read address
    channel_config_set_write_increment(&dmaPingPong0Config, true); //Increment write address
    channel_config_set_transfer_data_size(&dmaPingPong0Config, DMA_SIZE_32); //Transfer 32 bits each time
    channel_config_set_chain_to(&dmaPingPong0Config, dmaPingPong1); //Chain to the second pre-trigger dma channel
    channel_config_set_dreq(&dmaPingPong0Config, pio_get_dreq(capturePIO, sm_Capture, false)); //Set DREQ as RX FIFO
    channel_config_set_ring(&dmaPingPong0Config, true, 15); //Ring at 32768 bytes
    //Configure second capture DMA
    dma_channel_config dmaPingPong1Config = dma_channel_get_default_config(dmaPingPong1);
    channel_config_set_read_increment(&dmaPingPong1Config, false); //Do not increment read address
    channel_config_set_write_increment(&dmaPingPong1Config, true); //Increment write address
    channel_config_set_transfer_data_size(&dmaPingPong1Config, DMA_SIZE_32); //Transfer 32 bits each time
    channel_config_set_chain_to(&dmaPingPong1Config, dmaPingPong2); //Chain to the third pre-trigger dma channel
    channel_config_set_dreq(&dmaPingPong1Config, pio_get_dreq(capturePIO, sm_Capture, false)); //Set DREQ as RX FIFO
    channel_config_set_ring(&dmaPingPong1Config, true, 15); //Ring at 32768 bytes
    //Configure third capture DMA
    dma_channel_config dmaPingPong2Config = dma_channel_get_default_config(dmaPingPong2);
    channel_config_set_read_increment(&dmaPingPong2Config, false); //Do not increment read address
    channel_config_set_write_increment(&dmaPingPong2Config, true); //Increment write address
    channel_config_set_transfer_data_size(&dmaPingPong2Config, DMA_SIZE_32); //Transfer 32 bits each time
    channel_config_set_chain_to(&dmaPingPong2Config, dmaPingPong3); //Chain to the fourth pre-trigger dma channel
    channel_config_set_dreq(&dmaPingPong2Config, pio_get_dreq(capturePIO, sm_Capture, false)); //Set DREQ as RX FIFO
    channel_config_set_ring(&dmaPingPong2Config, true, 15); //Ring at 32768 bytes
    //Configure fourth capture DMA
    dma_channel_config dmaPingPong3Config = dma_channel_get_default_config(dmaPingPong3);
    channel_config_set_read_increment(&dmaPingPong3Config, false); //Do not increment read address
    channel_config_set_write_increment(&dmaPingPong3Config, true); //Increment write address
    channel_config_set_transfer_data_size(&dmaPingPong3Config, DMA_SIZE_32); //Transfer 32 bits each time
    channel_config_set_chain_to(&dmaPingPong3Config, dmaPingPong0); //Chain to the first pre-trigger dma channel
    channel_config_set_dreq(&dmaPingPong3Config, pio_get_dreq(capturePIO, sm_Capture, false)); //Set DREQ as RX FIFO
    channel_config_set_ring(&dmaPingPong3Config, true, 15); //Ring at 32768 bytes
    //Configure the DMA channels
    dma_channel_configure(dmaPingPong3, &dmaPingPong3Config, &captureBuffer[24 * 1024], &capturePIO->rxf[sm_Capture], 8192, false); //Configure the channel
    dma_channel_configure(dmaPingPong2, &dmaPingPong2Config, &captureBuffer[16 * 1024], &capturePIO->rxf[sm_Capture], 8192, false); //Configure the channel
    dma_channel_configure(dmaPingPong1, &dmaPingPong1Config, &captureBuffer[8 * 1024], &capturePIO->rxf[sm_Capture], 8192, false); //Configure the channel
    dma_channel_configure(dmaPingPong0, &dmaPingPong0Config, &captureBuffer[0], &capturePIO->rxf[sm_Capture], 8192, true);
}
void stopCapture()
{
    if(!captureFinished)
    {
        uint32_t int_status = save_and_disable_interrupts();
        if(lastCaptureType == CAPTURE_TYPE_SIMPLE)
            simple_capture_completed();
        else if(lastCaptureType == CAPTURE_TYPE_COMPLEX)
            complex_capture_completed();
        else if(lastCaptureType == CAPTURE_TYPE_FAST)
            fast_capture_completed();
        restore_interrupts(int_status);
    }
}
bool startCaptureFast(uint32_t freq, uint32_t preLength, uint32_t postLength, const uint8_t* capturePins, uint8_t capturePinCount, uint8_t triggerPinBase, uint8_t triggerPinCount, uint16_t triggerValue)
{
    //ABOUT THE FAST TRIGGER
    //
    //The fast trigger is an evolution of the complex trigger.
    //Like the complex trigger this is a sepparate program that checks for a pattern to trigger the capture program second stage.
    //
    //The main difference is the maximum length of the pattern to match and the sampling speed. This fast trigger
    //can only use a pattern up to 5 bits, but it captures at maximum speed of 100Msps (it could even sample up to 200Mhz but to match the
    //maximum speed of the sampling it is limited to 100Msps).
    //To achieve this the program occupies all 32 instructions of a PIO module, this is basically a jump table, each
    //instruction moves the pin values to the program counter except for the ones that match the pattern, which activate the
    //trigger pin using the side pins and create an infinite loop jumping to itself (basically a JMP currentpc SIDE 1).
    //
    //This solves the speed and latency problem, the speed reaches 100Msps and the latency is reduced to a maximum of 2 cycles, but
    //still can glitch on low speeds and also occupies a complete PIO module (but we have one unused, so its not a problem)
    //Too many samples requested?
    if(preLength + postLength >= (32 * 1024))
        return false;
    //Frequency too high?
    if(freq > 100000000)
        return false;
    //Incorrect pin count?
    if(capturePinCount < 0 || capturePinCount > 24)
        return false;
    //Bad trigger?
    if(triggerPinBase > 15 || triggerPinCount > 5 || triggerPinCount < 1 || triggerPinCount + triggerPinBase > 16)
        return false;
    //Clear capture buffer (to avoid sending bad data if the trigger happens before the presamples are filled)
    memset(captureBuffer, 0x00, sizeof(captureBuffer));
    //Store info about the capture
    lastPreSize = preLength;
    lastPostSize = postLength;
    lastCapturePinCount = capturePinCount;
    lastCaptureComplexFast = true;
    //Map channels to pins
    for(uint8_t i = 0; i < capturePinCount; i++)
        lastCapturePins[i] = pinMap[capturePins[i]];
    //Store trigger info
    triggerPinBase = pinMap[triggerPinBase];
    lastTriggerPinBase = triggerPinBase;
    //Calculate clock divider based on frequency, it generates a clock 2x faster than the capture freequency
    float clockDiv = (float)clock_get_hz(clk_sys) / (float)(freq * 2);
    //Store the PIO units and clear program memory
    capturePIO = pio0;
    pio_clear_instruction_memory(capturePIO);
    triggerPIO = pio1;
    pio_clear_instruction_memory(triggerPIO);
    //Configure 24 + 2 IO's to be used by the PIO (24 channels + 2 trigger pins)
    pio_gpio_init(triggerPIO, 0);
    pio_gpio_init(capturePIO, 1);
    for(uint8_t i = 0; i < capturePinCount; i++)
        pio_gpio_init(capturePIO, lastCapturePins[i]);
    //Configure capture SM
    sm_Capture = pio_claim_unused_sm(capturePIO, true);
    pio_sm_clear_fifos(capturePIO, sm_Capture);
    pio_sm_restart(capturePIO, sm_Capture);
    captureOffset = pio_add_program(capturePIO, &FAST_CAPTURE_program);
    //Input pins start at pin 2, 29 pins are captured
    pio_sm_set_consecutive_pindirs(capturePIO, sm_Capture, 2, 29, false);
    //Configure state machines
    pio_sm_config smConfig = FAST_CAPTURE_program_get_default_config(captureOffset);
    //Inputs start at pin 2
    sm_config_set_in_pins(&smConfig, 2);
    //Set clock to 2x required frequency
    sm_config_set_clkdiv(&smConfig, clockDiv);
    //Autopush per 29 bits
    sm_config_set_in_shift(&smConfig, false, true, 29);
    //Configure fast trigger pin (pin 1) as JMP pin.
    sm_config_set_jmp_pin(&smConfig, 1);
    //Configure interrupt 0
    pio_interrupt_clear (capturePIO, 0);
    pio_set_irq0_source_enabled(capturePIO, pis_interrupt0, true);
    irq_set_exclusive_handler(PIO0_IRQ_0, fast_capture_completed);
    irq_set_enabled(PIO0_IRQ_0, true);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), true);
    //Initialize state machine
    pio_sm_init(capturePIO, sm_Capture, captureOffset, &smConfig);
    //Configure trigger SM
    sm_Trigger = pio_claim_unused_sm(triggerPIO, true);
    pio_sm_clear_fifos(triggerPIO, sm_Trigger);
    pio_sm_restart(triggerPIO, sm_Trigger);
    //Create trigger program
    uint8_t triggerFirstInstruction = create_fast_trigger_program(triggerValue, triggerPinCount);
    //Configure trigger state machine
    triggerOffset = pio_add_program(triggerPIO, &FAST_TRIGGER_program);
    pio_sm_set_consecutive_pindirs(triggerPIO, sm_Trigger, 0, 1, true); //Pin 0 as output (connects to Pin 1, to trigger capture)
    pio_sm_set_consecutive_pindirs(triggerPIO, sm_Trigger, triggerPinBase, triggerPinCount, false); //Trigger pins start at triggerPinBase
    smConfig = FAST_TRIGGER_program_get_default_config(triggerOffset);
    sm_config_set_in_pins(&smConfig, triggerPinBase); //Trigger input starts at pin base
    sm_config_set_set_pins(&smConfig, 0, 1); //Trigger output is a set pin
    sm_config_set_sideset_pins(&smConfig, 0); //Trigger output is a side pin
    sm_config_set_clkdiv(&smConfig, 1); //Trigger always runs at half speed (100Msps)
    //Bypass input synchronizers
    hw_set_bits(&triggerPIO->input_sync_bypass, 0xFFFFFFFF);
    hw_set_bits(&capturePIO->input_sync_bypass, 0xFFFFFFFF);
    //Configure DMA's
    configureCaptureDMAs();
    //Enable capture state machine
    pio_sm_set_enabled(capturePIO, sm_Capture, true);
    //Write capture length to post program
    pio_sm_put_blocking(capturePIO, sm_Capture, postLength - 1);
    //Write capture end mark to post program
    pio_sm_put_blocking(capturePIO, sm_Capture, 0xFFFFFFFF);
    //Initialize trigger state machine
    pio_sm_init(triggerPIO, sm_Trigger, triggerOffset, &smConfig);
    //Enable trigger state machine
    pio_sm_set_enabled(triggerPIO, sm_Trigger, true);
    //Finally clear capture status and process flags
    captureFinished = false;
    captureProcessed = false;
    lastCaptureType = CAPTURE_TYPE_FAST;
    //We're done
    return true;
}
bool startCaptureComplex(uint32_t freq, uint32_t preLength, uint32_t postLength, const uint8_t* capturePins, uint8_t capturePinCount, uint8_t triggerPinBase, uint8_t triggerPinCount, uint16_t triggerValue)
{
    //ABOUT THE COMPLEX TRIGGER
    //
    //The complex trigger is a hack to achieve the maximum speed in the capture program.
    //To get to 100Msps with a 200Mhz clock each capture must be excuted in two instructions. For this the basic
    //capture programs (the positive and negative ones) use the JMP PIN instruction, this redirects the program flow based in the
    //state of a pin, so with an IN instruction and a JMP instruction we can create a loop that captures data until the trigger pin
    //is in the correct edge and then jumps to another subroutine that captures until the post-trigger samples are met.
    //
    //Unfortunately there is no way to jump to a subroutine based in the status of more than one pin, you can jump based in the
    //comparison of the scratch registers, but this requires more than one instruction to prepare the data.
    //So, what I have implemented here is an asynchronouss trigger, a second state machine running at máximum speed checks if the trigger
    //condition is met and then notifies to the first state machine. But... there is no way to notify of something between state machines
    //except for interrupts, and interrupts blocks the code execution (you WAIT for the interrupt) so this is not viable, so we use a hack, we
    //interconnect two pins (GPIO0 and GPIO1), one is an output from the trigger state machine and the other is the JMP PIN for the capture
    //state machine. When the trigger condition is met the output pin is set to 1 so the JMP PIN pin receives this signal and we can keep
    //our capture program to use two instructions.
    //This carries some limitations, the trigger can only work up to 66Msps but the capture can go up to 100Msps as they are independent.
    //Also, as the trigger always runs at maximum speed there may happen a glitch in the trigger signal for lower capture speeds, the
    //condition may be met but for less time than a capture cycle, so the capture machine will not sample this trigger condition.
    //Finally the trigger also has some cycles of delay, 3 instructions plus 2 cycles of propagation to the ISR, so a maximum of
    //25ns of delay can happen.
    //Too many samples requested?
    if(preLength + postLength >= (32 * 1024))
        return false;
    //Frequency too high?
    if(freq > 100000000)
        return false;
    //Incorrect pin count?
    if(capturePinCount < 0 || capturePinCount > 24)
        return false;
    //Bad trigger?
    if(triggerPinBase > 15 || triggerPinCount > 16 || triggerPinCount < 1 || triggerPinCount + triggerPinBase > 16)
        return false;
    //Clear capture buffer (to avoid sending bad data if the trigger happens before the presamples are filled)
    memset(captureBuffer, 0x00, sizeof(captureBuffer));
    //Store info about the capture
    lastPreSize = preLength;
    lastPostSize = postLength;
    lastCapturePinCount = capturePinCount;
    lastCaptureComplexFast = true;
    //Map channels to pins
    for(uint8_t i = 0; i < capturePinCount; i++)
        lastCapturePins[i] = pinMap[capturePins[i]];
    //Store trigger info
    triggerPinBase = pinMap[triggerPinBase];
    lastTriggerPinBase = triggerPinBase;
    //Calculate clock divider based on frequency, it generates a clock 2x faster than the capture freequency
    float clockDiv = (float)clock_get_hz(clk_sys) / (float)(freq * 2);
    //Store the PIO unit and clear program memory
    capturePIO = pio0;
    pio_clear_instruction_memory(capturePIO);
    //Configure 24 + 2 IO's to be used by the PIO (24 channels + 2 trigger pins)
    pio_gpio_init(capturePIO, 0);
    pio_gpio_init(capturePIO, 1);
    for(uint8_t i = 0; i < capturePinCount; i++)
        pio_gpio_init(capturePIO, lastCapturePins[i]);
    //Configure capture SM
    sm_Capture = pio_claim_unused_sm(capturePIO, true);
    pio_sm_clear_fifos(capturePIO, sm_Capture);
    pio_sm_restart(capturePIO, sm_Capture);
    captureOffset = pio_add_program(capturePIO, &COMPLEX_CAPTURE_program);
    //Input pins start at pin 2, 29 pins are captured
    pio_sm_set_consecutive_pindirs(capturePIO, sm_Capture, 2, 29, false);
    //Configure state machines
    pio_sm_config smConfig = COMPLEX_CAPTURE_program_get_default_config(captureOffset);
    //Inputs start at pin 2
    sm_config_set_in_pins(&smConfig, 2);
    //Set clock to 2x required frequency
    sm_config_set_clkdiv(&smConfig, clockDiv);
    //Autopush per 29 bits
    sm_config_set_in_shift(&smConfig, false, true, 29);
    //Configure comples trigger pin (pin 1) as JMP pin.
    sm_config_set_jmp_pin(&smConfig, 1);
    //Configure interrupt 0
    pio_interrupt_clear (capturePIO, 0);
    pio_set_irq0_source_enabled(capturePIO, pis_interrupt0, true);
    irq_set_exclusive_handler(PIO0_IRQ_0, complex_capture_completed);
    irq_set_enabled(PIO0_IRQ_0, true);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), true);
    //Initialize state machine
    pio_sm_init(capturePIO, sm_Capture, captureOffset, &smConfig);
    //Configure trigger SM
    sm_Trigger = pio_claim_unused_sm(capturePIO, true);
    pio_sm_clear_fifos(capturePIO, sm_Trigger);
    pio_sm_restart(capturePIO, sm_Trigger);
    //Modify trigger program to use the correct pins
    COMPLEX_TRIGGER_program_instructions[5] = 0x6040 | triggerPinCount;
    //Configure trigger state machine
    triggerOffset = pio_add_program(capturePIO, &COMPLEX_TRIGGER_program);
    pio_sm_set_consecutive_pindirs(capturePIO, sm_Trigger, 0, 1, true); //Pin 0 as output (connects to Pin 1, to trigger capture)
    pio_sm_set_consecutive_pindirs(capturePIO, sm_Trigger, triggerPinBase, triggerPinCount, false); //Trigger pins start at triggerPinBase
    smConfig = COMPLEX_TRIGGER_program_get_default_config(triggerOffset);
    sm_config_set_in_pins(&smConfig, triggerPinBase); //Trigger input starts at pin base
    sm_config_set_set_pins(&smConfig, 0, 1); //Trigger output is a set pin
    sm_config_set_clkdiv(&smConfig, 1); //Trigger always runs at max speed
    sm_config_set_in_shift(&smConfig, false, false, 0); //Trigger shifts left to right
    //Initialize trigger state machine
    pio_sm_init(capturePIO, sm_Trigger, triggerOffset, &smConfig); //Init trigger
    //Bypass input synchronizers
    hw_set_bits(&capturePIO->input_sync_bypass, 0xFFFFFFFF);
    //Configure DMA's
    configureCaptureDMAs();
    //Enable capture state machine
    pio_sm_set_enabled(capturePIO, sm_Capture, true);
    //Write capture length to post program
    pio_sm_put_blocking(capturePIO, sm_Capture, postLength - 1);
    //Write capture end mark to post program
    pio_sm_put_blocking(capturePIO, sm_Capture, 0xFFFFFFFF);
    //Enable trigger state machine
    pio_sm_set_enabled(capturePIO, sm_Trigger, true);
    //Write trigger value to trigger program
    pio_sm_put_blocking(capturePIO, sm_Trigger, triggerValue);
    //Finally clear capture status and process flags
    captureFinished = false;
    captureProcessed = false;
    lastCaptureType = CAPTURE_TYPE_COMPLEX;
    //We're done
    return true;
}
bool startCaptureSimple(uint32_t freq, uint32_t preLength, uint32_t postLength, const uint8_t* capturePins, uint8_t capturePinCount, uint8_t triggerPin, bool invertTrigger)
{
    //Too many samples requested?
    if(preLength + postLength >= (32 * 1024))
        return false;
    //Frequency too high?
    if(freq > 100000000)
        return false;
    //Incorrect pin count?
    if(capturePinCount < 0 || capturePinCount > 24)
        return false;
    //Clear capture buffer (to avoid sending bad data if the trigger happens before the presamples are filled)
    memset(captureBuffer, 0x00, sizeof(captureBuffer));
    //Store info about the capture
    lastPreSize = preLength;
    lastPostSize = postLength;
    lastCapturePinCount = capturePinCount;
    lastTriggerInverted = invertTrigger;
    lastCaptureComplexFast = false;
    //Map channels to pins
    for(uint8_t i = 0; i < capturePinCount; i++)
        lastCapturePins[i] = pinMap[capturePins[i]];
    //Store trigger info
    triggerPin = pinMap[triggerPin];
    lastTriggerPin = triggerPin;
    //Calculate clock divider based on frequency, it generates a clock 2x faster than the capture freequency
    float clockDiv = (float)clock_get_hz(clk_sys) / (float)(freq * 2);
    //Store the PIO unit and clear program memory
    capturePIO = pio0;
    pio_clear_instruction_memory(capturePIO);
    //Configure capture SM
    sm_Capture = pio_claim_unused_sm(capturePIO, true);
    pio_sm_clear_fifos(capturePIO, sm_Capture);
    pio_sm_restart(capturePIO, sm_Capture);
    //Load correct program, depending on the trigger edge
    if(invertTrigger)
        captureOffset = pio_add_program(capturePIO, &NEGATIVE_CAPTURE_program);
    else
        captureOffset = pio_add_program(capturePIO, &POSITIVE_CAPTURE_program);
    //Configure pins
    pio_sm_set_consecutive_pindirs(capturePIO, sm_Capture, 0, 32, false);
    pio_gpio_init(capturePIO, triggerPin);
    for(uint8_t i = 0; i < capturePinCount; i++)
        pio_gpio_init(capturePIO, lastCapturePins[i]);
    //Configure state machines
    pio_sm_config smConfig = invertTrigger?
                                NEGATIVE_CAPTURE_program_get_default_config(captureOffset):
                                POSITIVE_CAPTURE_program_get_default_config(captureOffset);
    //All pins are inputs
    sm_config_set_in_pins(&smConfig, 0);
    //Set clock to 2x required frequency
    sm_config_set_clkdiv(&smConfig, clockDiv);
    //Autopush per dword
    sm_config_set_in_shift(&smConfig, true, true, 0);
    //Configure trigger pin as JMP pin.
    sm_config_set_jmp_pin(&smConfig, triggerPin);
    //Configure interupt 0
    pio_interrupt_clear (capturePIO, 0);
    pio_set_irq0_source_enabled(capturePIO, pis_interrupt0, true);
    irq_set_exclusive_handler(PIO0_IRQ_0, simple_capture_completed);
    irq_set_enabled(PIO0_IRQ_0, true);
    irq_set_enabled(pio_get_dreq(capturePIO, sm_Capture, false), true);
    //Initialize state machine
    pio_sm_init(capturePIO, sm_Capture, captureOffset, &smConfig);
    //Bypass input synchronizers
    hw_set_bits(&capturePIO->input_sync_bypass, 0xFFFFFFFF);
    //Configure DMA's
    configureCaptureDMAs();
    //Enabl state machine
    pio_sm_set_enabled(capturePIO, sm_Capture, true);
    //Write capture length to post program to start the capture process
    pio_sm_put_blocking(capturePIO, sm_Capture, postLength - 1);
    //Write capture end mark to start capture
    pio_sm_put_blocking(capturePIO, sm_Capture, 0xFFFFFFFF);
    //Finally clear capture status, process flags and capture type
    captureFinished = false;
    captureProcessed = false;
    lastCaptureType = CAPTURE_TYPE_SIMPLE;
    //We're done
    return true;
}
bool IsCapturing()
{
    //If you need an explanation of this, you're a fool. :P
    return !captureFinished;
}
uint32_t* GetBuffer(uint32_t* bufferSize, uint32_t* firstSample)
{
    //If we don't have processed the buffer...
    if(!captureProcessed)
    {
        //Find capture end mark
        int32_t lastCapture = 0;
        for(int buc = 0; buc < 32768; buc++)
        {
            if(captureBuffer[buc] == 0xFFFFFFFF)
            {
                lastCapture = buc - 1;
                if(lastCapture < 0)
                    lastCapture = 32767;
                break;
            }
        }
        //Calculate the first sample index
        if(lastCapture < lastPreSize + lastPostSize - 1)
            lastStartPosition = 32768 - ((lastPreSize + lastPostSize) - (lastCapture - 1));
        else
            lastStartPosition = lastCapture - (lastPreSize + lastPostSize) + 1;
        uint32_t oldValue;
        uint32_t newValue;
        uint32_t currentPos = lastStartPosition;
        //Sort channels
        //(reorder captured bits based on the channels requested)
        if(lastCaptureComplexFast) //Was this a fast/complex capture?
        {
            for(int buc = 0; buc < lastPreSize + lastPostSize; buc++)
            {
                oldValue = captureBuffer[currentPos]; //Store current value
                newValue = 0; //New value
                for(int pin = 0; pin < lastCapturePinCount; pin++) //For each captured channel...
                    newValue |= (oldValue & (1 << (lastCapturePins[pin] - 2))) >> ((lastCapturePins[pin] - 2) - pin); //Store its value in the correct bit
                //Update value in the buffer
                captureBuffer[currentPos++] = newValue;
                //If we reached the end of the buffer, wrap around
                if(currentPos >= 32768)
                    currentPos = 0;
            }
        }
        else
        {
            //Same as for complex/fasst capture but without skipping the two first bits
            for(int buc = 0; buc < lastPreSize + lastPostSize; buc++)
            {
                oldValue = captureBuffer[currentPos];
                newValue = 0;
                for(int pin = 0; pin < lastCapturePinCount; pin++)
                    newValue |= (oldValue & (1 << lastCapturePins[pin])) >> (lastCapturePins[pin] - pin);
                captureBuffer[currentPos++] = newValue;
                if(currentPos >= 32768)
                    currentPos = 0;
            }
        }
        captureProcessed = true;
    }
    //Return data
    *bufferSize = lastPreSize + lastPostSize;
    *firstSample = lastStartPosition;
    return captureBuffer;
}

#endif